PowerVault 114X LTO4 drive - frequent problem inserting tape
Our customer is having an intermittent problem with their PowerVault 114X LTO4 drive. It's a standalone drive, not a changer. The unit just turned 3 years old last month, and has been out of warranty...
View ArticleReconstruction after Syswipe...
hello,Is there any possibility to restore or reconstruct array configuration after using syswipe on MD3000i?thanks I.
View Articlemd3000i Degraded Physical Disk Channel
Hi,I have an md3000i with attached md1000. We had a HDD fail which the hot spare took over with no down time or issues.Now I replaced the failed drive and it was put back into the array. Once that...
View Articlemd3000i + md1000 + 15x450Gb 15kSAS = Poor Performance
Morning,We recently acquired a used md3000i with an md1000 added shelf. The 3000i has 15x450Gb 15k SAS (in one RAID6 LUN) Dell drives. The 1000 has 15x 1Tb 7200rpm (in 2 RAID 6 LUNs).I have this...
View ArticlePower Supply / Cooling Fan issue
Hello there,I have problem in our PowerEdge MD36000f which is the left fan (Slot 1) has problem in the power supply. I called the service support this morning and the quality of the connection wasn't...
View ArticleDell CX4-120 Fault SPS and Failed/Removed status
Hello,I have a Dell CX4-120 reporting some faults.1\Disk array Enclosure Bus 0 Enclosure 1 is faulted2\Disk Processor Enclosure SPE is faulted3\Standby Power Supply SPE SPS B is faulted (I have checked...
View ArticleLUNs unknown group won't come online / rebuild Dell CX4-120
Hello,I have a dell emc cx4-120 2 enclosures Raid 6I have disk failed replaced and Show rebuild 0% I have found that if I put the failed disks back in they show as removed but rebuild 100%I can replace...
View ArticleDell EMC CX4-120 reset disk command?
Hello,I have disks reporting as removed i need the command or process on how to clear the removed flagtrying to restore the LUNs and disk arraryThanks Danny
View ArticlePlacing MD3220 controller on-line
A SAS controller was replaced on an MD3220. The controller now shows as being in service mode and the recovery guru walks through the steps to bring it on-line, the main step being go to...
View ArticleDell PowerVault 124T
Hi, i am new in dell world and i have a concern regarding powervault 124t tape loader. My Robotic library is DELL PV-124 T and my Tape Drive is IBM Ultrium-HH4. i have a backup solution called backup...
View ArticleMD3820i MPIO
I am running a MD3820i (storage) with 2 controllers. I have 4 nodes (server 2012 r2) configured and connected to the storage however it seems that only one path is being used.I read in a post that this...
View ArticleMD1000 slows way down on large file transfers
We have two MD1000 SAS storage arrays hooked up to a Dell R710 server. During a large file transfer (40+ GB) to one of the MD1000 arrays it will slow way down to a crawl. It looks as if it is slowing...
View ArticleNeed Win 7 Driver for PERC 9 h330 Mini
I need to install Win 7 64 on a Precision Rack 7910 workstation. The installation disk for SP1 doesn't have a driver for the RAID controller. The download from the 7910 support page is an exe file...
View ArticleDegraded Hard drive
Hi,We have poweredge R910 that is configured with 4 drive in RAID 5 and 2 drives in RAID 1 and othere 2 Drives Also in RAID 1.Now when I check the Manament server I can see that one of the disk of one...
View ArticleH310 Mini MessageID: STOR0210, Message: SCSI sense data (Sense key: B Sense...
R720xd with Perc H310 Mini.18 Drives16 of the drives are unraided.2 drives are Raid1 (they are the last two drives on the bus bays 16 and 17)O/S is Red Hat 6.7OMSA has started populating the messages...
View ArticleClik here to view.
Dell SC 2020 - Failed to re-balance ports
Hi ALLI have some problembutI can not find the cause of the problem!!zoning set
View ArticleNX4 Error
Hi All,following to power problems, our servers do not have access to the most NX4 storage.Checking by SSH (on Control Station), by running the command nas_checkup i get this...
View ArticleRaid Tiering?
Dear All,how does RAID Tiering work, especially in SC 2000 series? Is data moved between different RAID levels? Is it really physically moved or is there any abstraction layer? Is there any other name...
View ArticleAdd Disk Array to R620 with MD1200
I have a R620 server running Redhat Enterprise 6.4 connecting a MD1200 disk array with a H800 cardthe disk usage on the MD1200 disk array will be full soon. Can we add another MD1200 disk array to...
View ArticleEMC CX4-120, failed disk
Hi,I would replace a failed disk on my EMC Storage CX4-120It's out of warrenty, service tag <ADMIN NOTE: Service tag removed per privacy policy>How can we proceed?ThanksClaudio
View Article